71 RoadRunner bucket seats

71bird · Post by **71bird** » Wed Dec 18, 2013 10:07 am

I don't know's making them, I have seen them on ebay from time to time.

steved · Post by **steved** » Wed Dec 18, 2013 3:16 pm

Found them. one set is 55 bucks, the other is 24 and 7 shipping...

sjd

Post by **sdweatherman** » Wed Dec 18, 2013 10:16 pm

Here are the measurements if you or anybody else is interested. I noticed the reproductions on feeBay did not have the smaller holes. So if you made these Steve, they would be more correct. Another minor difference - look at the close up picture of the plates I posted. On each end of the diagonal cuts there is another 45 degree cut, so it actually comes out to the edge at 90 degrees. It kinda does the same on the drawing below. For metal thickness: It is slightly thicker than 1/8" - maybe 10% thicker. 1/8" = 0.125 then add another 10% - so about 0.1375 inches thick. Checked thickness table for mild steel, and 10 gauge steel is 0.1345 inches thick - so 10 gauge is my best guess for thickness on these plates.

Scott.

steved · Post by **steved** » Thu Dec 19, 2013 12:19 pm

rock.

thanks man!!

sjd

steved · Post by **steved** » Fri Dec 20, 2013 3:58 pm

Thanks Scott!! My vendor just knocked them out for me...

sjd

Post by **sdweatherman** » Fri Dec 20, 2013 10:06 pm

Wow! Those look nice! Probably won't be a huge demand for them, but someone will need them every once in a while for restos and conversions. Scott.

71Satellite98661 · Post by **71Satellite98661** » Sat May 30, 2015 1:31 pm

Those reinforcement plates look dead-on! I wish I would have noticed this thread before buying the not-as-accurate reproductions. Nice job!

steved · Post by **steved** » Mon Jun 01, 2015 8:40 am

Thanks!

I still have the file somewhere if anyone needs them!

sjd

71Beeper · Post by **71Beeper** » Sun Jan 29, 2017 1:20 pm

Hey Steved, I need a set of them.........lets deal.
How much for a set and how much to mail them to Southern Ontario, Canada?
Postal code is L8E 2J3.

ogopogo · Post by **ogopogo** » Mon Jan 30, 2017 2:26 pm

id prob take a set as well....

steved · Post by **steved** » Wed Feb 01, 2017 10:49 am

Hi guys! Let me see where that file went. it's been a couple years.

sjd

steved · Post by **steved** » Wed Feb 01, 2017 4:28 pm

71Beeper wrote:Hey Steved, I need a set of them.........lets deal.
How much for a set and how much to mail them to Southern Ontario, Canada?
Postal code is L8E 2J3.

do you have a waterjet shop in your area? I can send the .dxf file they need, and all you need is a piece of 10GA material. (.135", 3.5mm)

sjd

steved · Post by **steved** » Wed Feb 01, 2017 4:34 pm

ogopogo wrote:id prob take a set as well....

PM me, i'm getting a quote for some at the waterjet shop up the road from me.

sjd

71Beeper · Post by **71Beeper** » Wed Feb 01, 2017 9:13 pm

steved wrote:
71Beeper wrote:Hey Steved, I need a set of them.........lets deal.
How much for a set and how much to mail them to Southern Ontario, Canada?
Postal code is L8E 2J3.
do you have a waterjet shop in your area? I can send the .dxf file they need, and all you need is a piece of 10GA material. (.135", 3.5mm)

sjd

Yes, there is a water-jet cutting shop near me. Can you send me the .dxf file? Thanks.

steved · Post by **steved** » Wed Feb 08, 2017 9:49 am

I have 5 sets of these coming if anyone else is interested.

$50 + shipping.

Steve

Road Runner Nest

71 RoadRunner bucket seats

Re: 71 RoadRunner bucket seats

Re: 71 RoadRunner bucket seats

Re: 71 RoadRunner bucket seats

Re: 71 RoadRunner bucket seats

Re: 71 RoadRunner bucket seats

Re: 71 RoadRunner bucket seats

Re: 71 RoadRunner bucket seats

Re: 71 RoadRunner bucket seats

Re: 71 RoadRunner bucket seats

Re: 71 RoadRunner bucket seats

Re: 71 RoadRunner bucket seats

Re: 71 RoadRunner bucket seats

Re: 71 RoadRunner bucket seats

Re: 71 RoadRunner bucket seats

Re: 71 RoadRunner bucket seats