Front spring mounts rubber

Technical Question and Answer - On topic to 71-74 Plymouth B-bodies only.

Moderator: Site Administrators

Post Reply
User avatar
71_DEPUTY
Satellite Sebring (RH)
Posts: 66
Joined: Tue May 24, 2005 4:46 pm
Location: Collingwood, Ontario, Canada
Contact:

Front spring mounts rubber

Post by 71_DEPUTY » Mon May 22, 2006 2:35 pm

looking to see where the rubber is available for the 73 RR.

looked around but could source any!!

John Mac

1973 gtx/rr

Post by 1973 gtx/rr » Mon May 22, 2006 4:56 pm

To 71 Deputy,

If you are referring to the" rubber"for the K member bushings,then these are available in urethane from Performance Suspension Technologies.I did mine a couple of years ago as the originals
had dissintegrated and the results were well worth the investment. Hope this helps you.

User avatar
71_DEPUTY
Satellite Sebring (RH)
Posts: 66
Joined: Tue May 24, 2005 4:46 pm
Location: Collingwood, Ontario, Canada
Contact:

Post by 71_DEPUTY » Mon May 22, 2006 6:44 pm

nope- looking for the rear springs- perch mount onto the frame.

but thanks- haven't got to the front yet- will keep those in mind!!!!!!


John Mac

1bluegtx
GTX (RS)
Posts: 268
Joined: Fri May 06, 2005 1:05 am

Post by 1bluegtx » Mon May 22, 2006 9:04 pm

Does it still have the oval spring eyes?If so Energy suspension carries the bushings.You might want to consider changing to springs with round spring eyes as the oval ones are prone to breakage.

BRIAN
Its not numbers matching
It doesn't run on pump gas
And it doesn't purr like a kitten
11.73 at 115mph

User avatar
71_DEPUTY
Satellite Sebring (RH)
Posts: 66
Joined: Tue May 24, 2005 4:46 pm
Location: Collingwood, Ontario, Canada
Contact:

Post by 71_DEPUTY » Tue May 23, 2006 8:58 am

oval???? never seen those before- mine are round as a donut hole!!!! lol

ma mopar doesn't stock them anymore??????

got the rubber out of one this weekend- it has a outer steel cover- then rubber and then the innear steel section for the bolt to go through.

didn;t really look to bad- the outside was falling apart but the inside was still good.
guess for sitting for over 15 + years the rubber wasn't torn apart!!

1973 gtx/rr

Post by 1973 gtx/rr » Wed May 24, 2006 8:08 pm

Hey Dep,
Just looked thru my PST catalog and I think I found what you are looking for.They list a rear
spring polygraphite bushing kit for 73-79 B bodies for $100. US.They come in 1.5" or 2.0"
inside dia's.You can check them out at P-S-T.com

User avatar
71_DEPUTY
Satellite Sebring (RH)
Posts: 66
Joined: Tue May 24, 2005 4:46 pm
Location: Collingwood, Ontario, Canada
Contact:

Post by 71_DEPUTY » Wed May 24, 2006 9:07 pm

thanks- will check out their site!!!!!!

User avatar
71_DEPUTY
Satellite Sebring (RH)
Posts: 66
Joined: Tue May 24, 2005 4:46 pm
Location: Collingwood, Ontario, Canada
Contact:

Post by 71_DEPUTY » Thu May 25, 2006 2:16 pm

holy crapola!!!! buddy at NAPA found them for me!!!

part # NCP 274-6512 $ 11.01 and taxes in Candian dollars!!!!!!!!!!!! for two of them!!!!!!!!!!!

can't believe that- they look like they are $ 60-80 units!!!!!!!!!!!!

will try this weekend to put them in! will let you know if they are the right ones!!!!


this maybe a goody for the tech section???

Post Reply