Page 20 of 35
Re: Startin to work on the Clone Runner (it's PAINTED!)
Posted: Sat Feb 20, 2021 5:25 pm
by 71Beeper
Re: Startin to work on the Clone Runner (it's PAINTED!)
Posted: Sat Feb 20, 2021 5:27 pm
by 71Beeper
Re: Startin to work on the Clone Runner (it's PAINTED!)
Posted: Mon Feb 22, 2021 2:56 am
by 71440 gtx
Re: Startin to work on the Clone Runner (it's PAINTED!)
Posted: Mon Feb 22, 2021 8:06 am
by 71Beeper
Thanks Kevin.......too bad I didn't have a Dana to put in there eh??
Re: Startin to work on the Clone Runner (it's PAINTED!)
Posted: Mon Feb 22, 2021 10:36 am
by 71440 gtx
Re: Startin to work on the Clone Runner (it's PAINTED!)
Posted: Tue Feb 23, 2021 6:03 pm
by ct71rr
Very nice!
Re: Startin to work on the Clone Runner (it's PAINTED!)
Posted: Sun Feb 28, 2021 5:05 pm
by 71Beeper
Many Thanks guys
As the pieces go on it - its starting to look like a car again.
Not alot done this weekend.
Got the front signal lights installed.
- Feb 28 (1).jpg (82.29 KiB) Viewed 17153 times
- Feb 28 (2).jpg (113.36 KiB) Viewed 17153 times
- Feb 28 (3).jpg (71.71 KiB) Viewed 17153 times
- Feb 28 (4).jpg (126.13 KiB) Viewed 17153 times
- Feb 28 (5).jpg (105.58 KiB) Viewed 17153 times
Re: Startin to work on the Clone Runner (it's PAINTED!)
Posted: Sun Feb 28, 2021 5:07 pm
by 71Beeper
Re: Startin to work on the Clone Runner (it's PAINTED!)
Posted: Sat Mar 13, 2021 5:58 pm
by 71Beeper
While waiting for bits and pieces to come in I got a chance to sandblast the rear bumper mounts.
My neighbor has an industrial sand blaster in his shop & he allowed me to use it.
I can't believe it took nearly 2 hours to blast them....
Here they are just about to be blasted.
- March 5 (1).jpg (161.54 KiB) Viewed 17002 times
- March 5 (2).jpg (168.59 KiB) Viewed 17002 times
Here they are all done.
- March 5 (3).jpg (183.94 KiB) Viewed 17002 times
- March 5 (4).jpg (171.2 KiB) Viewed 17002 times
- March 5 (5).jpg (161.99 KiB) Viewed 17002 times
Re: Startin to work on the Clone Runner (it's PAINTED!)
Posted: Sat Mar 13, 2021 6:01 pm
by 71Beeper
Re: Startin to work on the Clone Runner (it's PAINTED!)
Posted: Sat Mar 13, 2021 6:07 pm
by 71Beeper
I put 2 coats of this stuff on to begin with as the steel was pock marked in some places.
- March 6 (7).jpg (96.5 KiB) Viewed 17002 times
While the primer was curing I started on the tail light housings.
First I stripped the gaskets and the sealer holding the gaskets on.
- March 7 (1).jpg (108.79 KiB) Viewed 17002 times
- March 7 (2).jpg (98.36 KiB) Viewed 17002 times
- March 7 (3).jpg (87.51 KiB) Viewed 17002 times
Next, the insides needed to be touched up to get that reflective coating back on.
- March 11 (1).jpg (137.55 KiB) Viewed 17002 times
Re: Startin to work on the Clone Runner (it's PAINTED!)
Posted: Sat Mar 13, 2021 6:14 pm
by 71Beeper
Before painting I did check that the wiring and the bulb sockets were okay, which they were.
I must note that these housings were not the ones that came off the car.
I bought these at a Mopar swapmeet some time ago.
Someone took the time to paint the outsides of the housings with grey paint....good job.
The originals were really bad and one of them the housing was cracked....
So after the first coat of reflective aluminum paint...
- March 11 (2).jpg (151.19 KiB) Viewed 17002 times
Then the finished second coat..
- March 11 (3).jpg (144.31 KiB) Viewed 17002 times
- March 11 (4).jpg (137.83 KiB) Viewed 17002 times
Here's a shot of one of the original housings....yikes!
- March 11 (5).jpg (158.43 KiB) Viewed 17002 times
Re: Startin to work on the Clone Runner (it's PAINTED!)
Posted: Sat Mar 13, 2021 8:19 pm
by 71440 gtx
Re: Startin to work on the Clone Runner (it's PAINTED!)
Posted: Mon Mar 22, 2021 8:25 pm
by 71Beeper
Now that the tail light housings are painted, it's time to fit the LED light bulbs.
- March 18 (1).jpg (118.03 KiB) Viewed 16910 times
Now to put some power to them (don't forget to ground the housings)...
- March 18 (2).jpg (114.47 KiB) Viewed 16910 times
- March 18 (3).jpg (120.7 KiB) Viewed 16910 times
My phone camera adjusted for glare.
- March 18 (4).jpg (83.56 KiB) Viewed 16910 times
Here's all three bulbs lit up.
- March 18 (5).jpg (90.95 KiB) Viewed 16910 times
Re: Startin to work on the Clone Runner (it's PAINTED!)
Posted: Mon Mar 22, 2021 11:30 pm
by sdweatherman
Very cool. I plan to do the same thing. I might have to replace my sockets in my housings first tho. Let us know what the part numbers are on the bulbs - looks like a shorter one for the reverse lights? You need to slow down - you are getting too far ahead of me...